Hair dryer is a device to dry the hair after bathing or shampooing. This tool is generally used in private by women, besides being used in beauty salons, printing company, printing photos, and others.
Over time this tool will decrease the quality suffered damage to its components, in addition to the damage can occur due to old age or use too often. Before discussing how to fix Hair dryer would be helpful to know the parts of the tool along with how it works.
Hair dryer parts
Cables connecting devices to an electrical outlet
Agency tool
Fan speed control motors
filament / heater coil
How it works Hair dryer
At the time of the connecting cable is connected to a power outlet, the power will go into the speed control switch.
When we press the power button, the speed control will flow from the connecting cable to the switch and then forwarded to the motor of the fan and the filament (heater coil) then immediately turn around with a motor to move / rotate the fan, along with it, the filament will become hot due electrified .
With the rotation of the fan and overheating in the filament will exhaled air from outside or driven by a fan to pass through the hallway whose walls are surrounded by hot filament, so the air is exhaled by the fan will be pushed out in hot conditions because heated by the filament.
When the speed control button is located on the low position of the rotation motor of the fan is on slow rotation position so that exhaled air less.
When the switch pengatuir motor speed is at a hight position then the fan rotation will be faster so that hot air is blown there will be more. so it goes the fan and the filament will work together when a key regulator of motor speed on the on position.
Symptoms of damage that often occurs in Hair dryer:
total dead
The fan does not spin but the tool body is hot
Hair dryer fan spins but no heat
The fan spins but does not heat the air out of money
Round Hair dryer abnormal tau seeprti halting slow.
total dead
This occurs due to the possibility of electrical connecting cable is disconnected or the cable that goes to the speed control switch regardless. Check the cable connecting the physical basis there may be a drop out from being bitten by rats. Or check using AVO meter RX1Kohm, if you do not have the AVO meter in the house then you can use tespen instead, by way of opening the body Hair dryer until it looks all parts then insert the connecting cable into an outlet. Stick it to each connector end tespen in dalamnuya, mark the part that can not turn on tespen, bial have found that damage to immediately repair the appropriate components.
The fan does not spin but the tool body is hot
This can occur due to damage to the motor of the fan, it may be a carbon brush that has been discharged or windings on the motor burned out. Carbon brush is a connector that connects the cable to the motor in order to rotate. Carbon brush can be depleted as a result of friction with the motor that is always moving.
Hair dryer fan spins but no heat
this is due to the filament / heater coil broke, when the coil broke immediately replace it with a new one.
Round Hair dryer is not normal, such as stuttering or slow
There are two possibilities when it happens, namely:
carbon brush is already thin
mati.Untuk carbon brush motor capacitors are already thin and dead capacitors can replace them with the appropriate.
Thus a brief review I on how to fix Hair dryer, may be useful for you.
Thursday, August 28, 2014
HOW TO USE, USE HAIR DRYER
Hair dryer or hair dryer is a tool to speed up the drying process of hair, this tool is used some time after bathing or shampooing, people usually do at the moment will face certain events such as an invitation to a party or go to a place of importance.
It works by blowing air from the outside by means of a small fan to get into a hot area in the instrument to be forwarded to the drain holes. For those of you who have recently had or who would like to know how to use a blow dryer please read the description below:
1, Once you wet the hair with shampoo or bath, the way things need to be done before using a hair dryer to reduce the moisture content is found on the scalp and hair by means of pressing the hair with palms slowly until no more water droplets of hair.
2 Once the moisture content in the hair and scalp is reduced then the next step is to straighten the hair with a comb grooves using fingers comb tenuous, so of hair will follow the direction of the straight comb without a hitch, use the comb fingers tenuous point is to avoid breaking the hair.
3 Prepare your hair dryer, and insert the connector plug into an outlet and then turn it on by pressing the switch a hair dryer with the index finger placed at the position of the switch position is slow (low).
4.Start dry your hair with a hair dryer in a way closer to the tip of the hair with a minimum distance of 15cm as she pushed her hair
5. Do drying to the hair, try not to position the hair dryer too long in one place because it will result in hair damage.
6 Stop using a hair dryer when the hair is not too dry, let your hair dry naturally in the not too long. How this is done in order to awake the beauty and health of hair.
7 After the drying process is complete place it in a sheltered spot a hair dryer because the new hair dryer used still hot.
8. drying hair using a hair dryer should not be too often because it was feared would make the hair easily damaged, branched and changed color so that it will reduce the beauty of the hair, you should let your hair dry naturally more awake to the beauty, strength, and health.
9 In addition to dry hair turns a hair dryer can also be used to dry other items such as:
Drying clothes during the rainy season, usually during the rainy season the sun is not too hot so that the clothes are dried in the sun to dry in a short time is difficult but we can overcome that is by using a hair dryer, the way is to hang clothes and then heated with a hair dryer, in this process should note the fabric is dried, if made of materials that are not heat resistant so keep the distance a hair dryer with the clothes do not do it too long or quite a few moments and let the clothes dry.
Drying the mobile phone is submerged in water, the way is open throughout the screws then remove each part carefully then one by one each Dry the parts using a hair dryer, hair dryer with a distance between the components of the dekeringkan minimum of 20cm, is intended to prevent damage components are sensitive to heat. After all parts dries attach back to normal mobile phone and then try to turn on and use it. HP will usually return to normal when no water stuck in it, this applies to HP instantly when submerged in water is turned off or its battery is immediately revoked, because if the water lingering soak HP that are still turned on will result in a short circuit / short-circuit components.
Drying the paper money or other valuable paper soaked with wet from washing water when washing clothes proes. how dry it is to put paper money sticking together on the table and then blow your hot air from a hair dryer to the top layer of paper money then let the top layer of the money after it dries separate bills that have been dried to another place, so it goes until the money layer the latter.
It works by blowing air from the outside by means of a small fan to get into a hot area in the instrument to be forwarded to the drain holes. For those of you who have recently had or who would like to know how to use a blow dryer please read the description below:
1, Once you wet the hair with shampoo or bath, the way things need to be done before using a hair dryer to reduce the moisture content is found on the scalp and hair by means of pressing the hair with palms slowly until no more water droplets of hair.
2 Once the moisture content in the hair and scalp is reduced then the next step is to straighten the hair with a comb grooves using fingers comb tenuous, so of hair will follow the direction of the straight comb without a hitch, use the comb fingers tenuous point is to avoid breaking the hair.
3 Prepare your hair dryer, and insert the connector plug into an outlet and then turn it on by pressing the switch a hair dryer with the index finger placed at the position of the switch position is slow (low).
4.Start dry your hair with a hair dryer in a way closer to the tip of the hair with a minimum distance of 15cm as she pushed her hair
5. Do drying to the hair, try not to position the hair dryer too long in one place because it will result in hair damage.
6 Stop using a hair dryer when the hair is not too dry, let your hair dry naturally in the not too long. How this is done in order to awake the beauty and health of hair.
7 After the drying process is complete place it in a sheltered spot a hair dryer because the new hair dryer used still hot.
8. drying hair using a hair dryer should not be too often because it was feared would make the hair easily damaged, branched and changed color so that it will reduce the beauty of the hair, you should let your hair dry naturally more awake to the beauty, strength, and health.
9 In addition to dry hair turns a hair dryer can also be used to dry other items such as:
Drying clothes during the rainy season, usually during the rainy season the sun is not too hot so that the clothes are dried in the sun to dry in a short time is difficult but we can overcome that is by using a hair dryer, the way is to hang clothes and then heated with a hair dryer, in this process should note the fabric is dried, if made of materials that are not heat resistant so keep the distance a hair dryer with the clothes do not do it too long or quite a few moments and let the clothes dry.
Drying the mobile phone is submerged in water, the way is open throughout the screws then remove each part carefully then one by one each Dry the parts using a hair dryer, hair dryer with a distance between the components of the dekeringkan minimum of 20cm, is intended to prevent damage components are sensitive to heat. After all parts dries attach back to normal mobile phone and then try to turn on and use it. HP will usually return to normal when no water stuck in it, this applies to HP instantly when submerged in water is turned off or its battery is immediately revoked, because if the water lingering soak HP that are still turned on will result in a short circuit / short-circuit components.
Drying the paper money or other valuable paper soaked with wet from washing water when washing clothes proes. how dry it is to put paper money sticking together on the table and then blow your hot air from a hair dryer to the top layer of paper money then let the top layer of the money after it dries separate bills that have been dried to another place, so it goes until the money layer the latter.
HAIR DRYER
Basic theory
A hairdryer airplane has three main parts: a motorcycle, a heating element and fan. When the rotating plane, carrying hot heating element and a fan blowing hot air flow out through the bars of the elements. Switches that operate aircraft having one or more positions. Some hair dryers have multiple switches, a motor controller and a controller or two heating elements. Many hairdryer is placed in a plastic house seal; This house can not be disassembled for repair. If the aircraft does not work, take it to a professional service aircraft. Estimate the cost of repairs before the specified improvements; how much it cost to replace it with a new aircraft when compared to fix it.
Caution: Before doing some work on the hair dryer, make sure that the plug has been detached plane.
Cleaning and Lubrication
Components in the hairdryer collect a lot of dirt; when the aircraft rotates, dust and hair sucked enter the inlet air stream. Take it apart and the periodic component parts, and check the terminal on the unit. If the terminal on fire, dirty, or corroded, clean them with steel wool (steel wool) Good and soft cloth. Remove hair and dirt from all parts. Clean the motor shaft and bearing fan that spins, and lubricate these parts with a clear oil Household - Sewing machine oil is also good.
When you clean the plane, check switch ON / OFF and, if the aircraft have it, the controller switches the heating element. Clean and tighten the switch terminals. If the switch is clogged dirt, disconnect the end of the wire to it and remove dirt from the switch. Spray terminal switch with electrical contact cleaner, can be obtained (available) in the aircraft repair and supplier of electrical components. Return the switch to normal and so on while insert cleaner on the moving parts, and rub with a soft cloth to clean it; then reinstall.
heating More
Because of the heat generated by the elements is very high, the aircraft has a safety overload, which will turn off the heating element when the round heat generated is too high. If the aircraft stops spinning when in use, disconnect the power source to the aircraft and allow aircraft to cool for 30 minutes or more; Please check again later. If the aircraft works, the problem is more simple heat; Safety thermal overload has been decided and, as the plane is cold, it will reset itself. If the aircraft does not work after cooling for 30 minutes, safety loads more - in many ways is the thermostat thermodisc (chip-hot) - usually placed on the heating element. Look for the section curves and convex on the bimetallic with a diameter of about 1 inch.
To determine the safety overload again broken, Test it by AVO, set on RX1 scale; meter will point to zero. If the load is damaged safety, replace with a new one that is similar. Remove the old one, and connect the new security in the same way as the old connection.
Heating element
Some hair dryers have a heating element; some have 2 elements. If the plane died when in use, and a safety overload is not damaged, the problems usually occur damage to the heating element. Open plane and test elements. If the element is damaged, loose, or hanging, it must be replaced. Replace it with a new element similar. Remove the screws that hold the old elements, the electrical disconnect and remove the old element. If the old element can not be disassembled from its place, take a plane to a professional service, or, if the aircraft is not expensive, replace it with a new one.
switches
Many hair dryers have a switch ON / OFF control of the motor and one or two additional switch - if there are 2 heating elements, it is possible there are 2 switch - a set position on the heating element. This switch is usually connected series; if the motor does not rotate because the switch ON / OFF does not work, the element will not heat. If the motor spins but no heat coming out, the controller switches the heating element may be damaged. If the elements of the two plane elements are not too hot, check the overload safety measure before testing the switch element.
Switch often does not work because dirty. If the motor does not spin or the element is not hot, clean the switch with contact cleaner, as described above. If the problem is not solved, and if the heating element and the motor does not not damaged, Test it switches to the AVO, set on RX1 scale, the meter should read zero. If the switch is damaged, replace it with a new one that is similar. Connect the new switch in the same way as the old connection.
fan
If the hair dryer can not exhale completely, or if he can not produce hot air in sufficient quantities, may be bound for dirty fan or hair coiled coils on the fan blade. Take it apart and clean the aircraft and the motor shaft bearing fan rotation. Lumasilah this section with a light oil Household - Sewing machine oil is also good. Rotate the fan by hand to test it. If the fan can not rotate easily, replace the fan with a new one that is similar. Remove the old fan with the release bearing and fan pulley on the motor shaft. Place the new fan on the motor shaft and connect in the same way as the old connection; then replace the pads.
If the fan is not attached, the fan blade Test it; blade made of metal or plastic. Metal fan blades can be bent; bend properly so it can be returned to normal with pliers. If there is a curved blade, replace the fan as described above. Plastic fan blade may break or destroyed; if the blade is damaged, replace the fan with a new one that is similar.
Motor
If the motor does not rotate, aircraft loading and turn the motor shaft by hand. If it is too hard to spin, lumasilah RT motor with light oil - also good sewing machine oil. Rotate the shaft to spin freely again. Sometimes the aircraft will rotate normally and then suddenly start blowing cold air; This is caused by the slow rotation of the motor. Dust and hair that is carried by the flow of air inside the plane can continue to enter the motor bearing, slow rotation of the motor and cause more heat and stopped. Remove the fan and bearings, and clean the fan, bearing, and shaft of the motor. Then reassemble the parts.
If cleaning and lubrication can not make the motor spin, if the motor can not be rotated by hand, or if the motor hard, take a plane to the professional service.
Place the new fan on the motor shaft and connect in the same way as the old connection; then replace the pads.
If the fan is not attached, the fan blade Test it; blade made of metal or plastic. Metal fan blades can be bent; bend properly so it can be returned to normal with pliers. If there is a curved blade, replace the fan as described above. Plastic fan blade may break or destroyed; if the blade is damaged, replace the fan with a new one that is similar.
Motor
If the motor does not rotate, aircraft loading and turn the motor shaft by hand. If it is too hard to spin, lumasilah RT motor with light oil - also good sewing machine oil. Rotate the shaft to spin freely again. Sometimes the aircraft will rotate normally and then suddenly start blowing cold air; This is caused by the slow rotation of the motor. Dust and hair that is carried by the flow of air inside the plane can continue to enter the motor bearing, slow rotation of the motor and cause more heat and stopped. Remove the fan and bearings, and clean the fan, bearing, and shaft of the motor. Then reassemble the parts.
If cleaning and lubrication can not make the motor spin, if the motor can not be rotated by hand, or if the motor hard, take a plane to the professional service.
|
problems
|
Possible Causes
|
solving
|
| Plane does not rotate | 1. No daya2. POWER3 cable damage. Switch ON / OFF kotor4. Switch ON / OFF rusak5. Kotor6 switch elements. Rusak7 switch elements. Motor damaged | 1 Check the power cord, plug, and KK. Check-safety lawyer melting or CB on the main panel; perba-kirangkaian.2. Test it cable; if damaged, gantilah3. Clean switch ON / OFF4. Test switch ON / OFF; if damaged, gantilah5. Clean the switch element of switch elements 6 tests; if damaged, replace 7 Bring to a professional service, or replace plane. |
| voltage plane | 1 The power cable is damaged, 2 Electrical system hu-man short. |
1 Test cable; replace if damaged, 2. Bring to a professional service |
| Hot air but the fan does not spin | 1 fan dirty; fans need lubrication, 2 motor shaft needs to be lubricated, 3 Motor defective | 1 Clean and lumasilah fan, 2 Lumasilah motor shaft and sleepers, 3 Bring to a professional service or replace aircraft. |
| Fans spin but the aircraft is not hot | 1 switch element is dirty, damaged 2 switch element, 3 switch ON / OFF the dirty, 4 switch ON / OFF damaged, 5. Safety lebihrusak load, 6 faulty heating element. | 1 Clean the switch element, 2 Test it switch element; if broken, replace, 3 Clean the switch ON / OFF, 4 Test it switch ON / OFF; if broken, replace, 5. Test it loads more safety; if broken, replace, 6 Replace the heating element, or replace aircraft. |
Tips on Wearing Hair Dryer With True
Tips and tricks that you can use to keep the hair from the bad effects of the blow dryer.
Use Hair Serum
To protect the hair cuticle from heat exposure, you can protect your hair with a special serum. This serum can you get at various stores that sell cosmetics or salon equipment. This serum can protect hair from heat exposure such tools salon hair dryer or a vise.
Never Too Hot
Hair dryer typically has a heat level. It would be better if you use cold or warm wind. Avoid using air that is too hot. The more heat, the more likely damage your hair.
Keep Distance
Taking into account the distance between the hair dryer and the hair is very important. When you use a hair dryer too close, then more heat on the hair. The best distance is about 20 cm.
Move Hair Dryer
Many women simply shake a hair dryer, not the move to all parts of the hair. As a result, some parts are more frequently exposed to the blow dryer heat exposure. That part is more susceptible to problems such as dry and brittle. So do not be lazy and do not move a hair dryer too long silence on the part of the hair.
Hopefully these tips helpful for you.
Use Hair Serum
To protect the hair cuticle from heat exposure, you can protect your hair with a special serum. This serum can you get at various stores that sell cosmetics or salon equipment. This serum can protect hair from heat exposure such tools salon hair dryer or a vise.
Never Too Hot
Hair dryer typically has a heat level. It would be better if you use cold or warm wind. Avoid using air that is too hot. The more heat, the more likely damage your hair.
Keep Distance
Taking into account the distance between the hair dryer and the hair is very important. When you use a hair dryer too close, then more heat on the hair. The best distance is about 20 cm.
Move Hair Dryer
Many women simply shake a hair dryer, not the move to all parts of the hair. As a result, some parts are more frequently exposed to the blow dryer heat exposure. That part is more susceptible to problems such as dry and brittle. So do not be lazy and do not move a hair dryer too long silence on the part of the hair.
Hopefully these tips helpful for you.
Subscribe to:
Posts (Atom)